CPU:

KDF11B LSI-11/23-PLUS M8189 (Digital_Microcomputer_Products_Handbook_1985, 4.1- (p.63-)

CPU in E75, MMU in E74

Manufacturer Test Jumpers are default:
J6-J7
J8-J9
J20-J21
J35-J34 J33
J25 J26 - J27

J10-J11 : sets line clock interrupt enable FF and allows Q-bus BEVENT for prog interrupts.
J12 open : SLU2 is at 776500
J13 open : SLU2 enabled
J14 open : SLU1 (console) enabled
J15 open : boot/diag registers, ROMs and line clock reg. enabled

J16 open : Halt/Trap
J17 open :
J18-J19  : Bootstrap

E114/S2-1 to S2-4 set to 9600 Baud for SLU1/Console (S2-4-1: off-off-on-on)
J42-J43 installed internal Baud Rate generator
J41 open

SLU1/Console:
J39 open : 8-bit characters
J37-J38  : one stop bit
J36 open : Parity check disabled
J40 open : Even Parity (not meaningful with J36 open)

J3 open : 
J4-J5   : Break/Halt disabled

E114/S2-5 to S2-8 set to 9600 Baud for SLU2 (S2-8-5: off-off-on-on)
SLU2:
J31 open : 8-bit characters
J29-J30  : one stop bit
J28 open : Parity check disabled
J32 open : Even Parity (not meaningful with J28 open)

E102/S1- to S1-4 Diagnostics/Bootstrap switches
S1-1 on : CPU diagnostics executed at powerup
S1-2 on : memory diagnostics executed at powerup
S1-3 off: DECnet boot disabled
S1-4 on : Console test and dialogue

S1-5 to S1-8 DECnet and Turnkey boot options set to (S1-5-8: off-off-on-on) TU58 boot

J22-J23 : Boot & diagnostics EPROM option (EPROMs are installed)
J24 open : Boot & diagnostics ROM option

Backplane jumpers W1 & W2 installed

====================================

Tested with two different memory cards:

M8067 MSV11-PL 9 * 8 NEC4164: 256 kWord (Digital_Microcomputer_Products_Handbook_1985, 14.1- (p.201-)

J6-J7 : installed 
J8 open :
J21 open :
J22-J23 : inhibit
J44-J45 : installed
J43 open :
J1, J2, JY, JX, JW, JV open : Starting Address Jumpers - 0-248 K
JU, JT, JS, JR, JP, JN, JM, JL open : Starting Address Jumpers - 0 K
JA, JB, JC, JD, JE open : CSR Address Jumpers - 0o772104
JF, JH open : Misc, always open

W1 installed  (bus Grant Continuity)
W2 installed  (bus Grant Continuity)
W4 installed  (always)
W5 installed  (always)
W9 installed  (only non-battery backup)
W12 open      (battery backup)
W13 installed (only non-battery backup)
W14 open      (battery backup)
W15 installed (only non-battery backup)

====================================

M7551 MSV11-QB 18 * 4 KM41256AP: 2048 kWord (Digital_Microcomputer_Products_Handbook_1985, 15.10- (p.220-)

J1-J2 : test jumper
J3 open :
J12-J13 : test jumper
J14 open :
J15 open : 
J16-J17 : test jumper

J4-J5   : CSR register selection (off) card is second memory board.
J6-J7   : CSR register selection (on)
J8-J9   : CSR register selection (on)
J10-J11 : CSR register selection (on)

SW2 Starting address (@512Kbytes - SW2-1-6: on-on-off-off-off-off. @0Kbytes - on-on-on-on-on-on-on)
SW1 Ending address (@2048kbytes - SW1-1-5: on-on-on-on-off-off)

W1  : Battery backup jumper.
W30 : Battery backup jumper.